UV Resistant to Climate Testing Machine

General Information 
This equipment uses the best simulation sun UV spectra of fluorescent UV lamps and the combination of temperature control, for the wet device to simulate the material causing discoloration, brightness, strength reduction; cracking, flaking, powder, oxidation and other damage to the sun (UV) high temperature, high humidity, dew, dark cycle etc, at the same time by ultraviolet light and moisture of synergy between the single material or single capacity of water logging resistance light fastness ability abate or failure, which is widely used in the material resistant to climate performance evaluation. 

This equipment can simulate the prime UV level of shining to make fluorescent lamp, combined with temperature control, humidity system, assume material discolored, shining strength lowed, broken, peeling, powdered, oxidized in UV level, high temperature, high humidity, fog, darkness or their cooperation, affect the materials single light & humidity resistance capability. This machine can provide good UV light, low price, easy operation, test itself by programme, automatic testing, stable light strength, high recurrent of same test result. 
Kind of test using the equipment: 
- UV test for photovoltaic (PV) modules. (IEC 61345) 

Features 
- Controller: touch-screen 
- Show UV strength and value, RS-485 connector 
- Temperature Sensor: PT100 temperature sensor 
- Temperature & humidity control by: BTHC 

Technical Specifications 
- Temperature range: RT+10℃ ~ 70℃ 
- Temperature uniformity: ≤2°C 
- Degree of temperature fluctuation: ≤±0.5°C 
- Humidity range: RH ≥90％ 
- Environmental temperature: RT+15°C~35°C 
- Environmental humidity: ≤85% RH 
- Lamp center distance: 70±2 mm 
- Center distance between specimen and lamp: 50±2 mm 
- Lamp model: UV-A, 40W, AC 220 V / UV-B, 40 W, AC 220 V. 
- Wavelength: 315~400 nm / 280~315 nm 
- Number of lamps: 8 
- Equipment weight: ≥100 kg 
- Internal dimension: 450 × 1100 × 500 mm (W×L×H). 
- Illumination dimension: 450 × 260 mm (L × H) 
- Power: AC 220V ± 10%; 50Hz; 3 kW
- Lamp’s service life: 1600 H

Xenon Light Resistant to Climate Testing

General Information 

This equipment is on the analogue terrestrial solar radiation is widely used to determine the electrical, climatic adaptability of electronic products on the resistance of the solar radiation environment and the temperature and humidity environment (in particular changes in the electrical and mechanical properties) can also be used tolerate some corrosion in the check sample. 

Kind of test using the equipment: 

- Xenon UV test. (IEC 61730-1) 

Features 

- Light source: Air-cooling xenon lamp 

- Internal material: SUS3042B stainless steel panel. 

- External material: cold rolled plate/injected plastics. 

- Cooling system: air-cooling type. 

- Controller: used to control temperature, humidity, radiant intensity and working
  time. 

- Black panel temperature. 

- Speed controller. 

Technical Specifications 

- Radiant intensity: 500W/㎡〜1100W/㎡ 

- Lamp power: 3.3 kW 

- Test bench, dynamic rotary test bench, rotating speed ≥1r/min, and steeples speed
  control.

- Test specimen: 50 mm x 200 mm (W x H), 30 specimens in total
  (standard specimen).

- Spectral wavelength: 350-850 nm 

- Temperature range: 20℃〜100℃ (±2℃) 

- Black panel temperature: 40〜110℃ 

- Humidity: 30%〜60% under radiation and up to 98% in black. 

- Temperature deviation: ±1℃; humidity deviation: ±2% (to be measured 30 minutes
  after the stabilization of temperature sensing). 

- Temperature uniformity: ±2℃；humidity uniformity: ±3% (to be measured 30 minutes
  after temperature stabilization at positions, 1/6 away from each wall surface in
  test area. 

- Heating time: from room temperature to 100℃, within 50 minutes (no load). 

- Inner dimension of chamber: test area, 950 × 950 × 800 mm (W × H × D). 

- Overall dimension of chamber: 1400 x 1750 x 1250 

- Power supply: AC 380V, 50HZ and 10 kW, maximum current: 11 A 

- Spraying time: 1〜9999 minutes.
- Spraying cycle: 1〜240 minutes

Vibration Tester

General Information 

The system machines of Amplitude modulation frequency modulation sweep frequency are consist of vibration table、vibration body and controller table. 

The design of the machine is based on the humanization principle with its beautiful appearance. 

The use of the machine is easy and convenient with most of its quite voice when it is working. That’s why it is do not need special requirement for installation. 

The machine works so reliable and stable with the inside design could make protection for obstruction circuit which caused by the strong magnetic field for weak current control. 

Kind of test using the equipment: 

- Vibration test (sinusoidal). (IEC 60068-2-6) 

Features 

- Vibration direction (YZ): vertical/horizontal. 

- Cooling method: Air cooling 

- Constant frequency & scanning setting 

Technical Specifications 

- Test load: 40 Kg 

- Frequency range: 5-200 Hz 

- Scanning frequency: 5-200 Hz 

- Displacement amplitude (adjustable P-P): 0-5 mm 

- Time range: 1-350000 S 

- Dimension of working table: 450 x 450 x 46 mm (LxWxH). 

- Overall dimension: 1200 x 500 x 450 mm (LxWxH) 

- Control cabinet dimension: 500 x 380 x 1050 mm (LxWxH). 

- Power: 2.2 kW

- Power supply voltage: 220/50 ±2%

Hardness Tester

General Information 

HM manual horizontal test rack is designed for pointer type push-pull gauge and digital type push-pull gauge in pull-compression test and insert-withdrawal test, etc. 

It is specialized for and fracture test in every trade and scientific research organization. It can be used on various working table. It has the advantage of manual operation, simpleness and tranquilization. 

Kind of test using the equipment: 

- Determination of hardness 

(IEC 60502-1, IEC 60502-2, SNI IEC 60502-1, SNI IEC 60502-2) 

Features 

- Manual, stable and easy to access; can be installed on table or work. 

- Bench to make sure that the rack is more stable. 

- Specification parameters of digital. 

- Type push-pull gauge (built-in). 

Technical Specifications 

- Distance: 100 mm 

- Maximum load: 1000 N 

- Overall dimension: 450 × 160 × 210 mm (L × W × H)

- Net weight: 9.6 kg

Hardness Tester / HC Wheel Manual Test Stand

General Information 

This equipment is large machine base ensures perfect stability, very suitable for test on indoor table. Trapezoidal screw is used for rotation with side hand wheel loading. This equipment may be installed on a table or bench surface. It is equipped with a standard platform for the base. 

HC Wheel Manual Test Stand is specially designed to match all kinds of Push Pull Gauge and can be combin ed into various test stands.Applied in various test,such as swithc test,insertion,withdraw and fracture test.When it display the force value,it can display the stroke by install Digital Stuff. 

Kind of test using the equipment: 

- Determination of elastic modulus 

(IEC 60502-1, IEC 60502-2, SNI IEC 60502-1, SNI IEC 60502-2) 

Features 

- Stable base, handwheel overload, easy operation. 

- It has motive carrier on the base,so it is convenient to fix clamps. 

- Digital scale available to collect real-time journey data (HCS). 

Technical Specifications 

- Rated load: 500 N 

- Stroke：≤170 mm
- Weight：18kg